METALLURGICAL AND MATERIALS TRANSACTIONS A
	TABLE OF CONTENTS Volume 28A, No. 11, November 1997 This Month Featuring: Alloy Phases; Transformations; Mechanical Behavior; Environment; Welding & Joining; Solidification; Materials Processing; Composite Materials. View November 1997 Abstracts.

Alloy Phases

The Evolution of Solutions: A Thermodynamic Analysis of Mechanical Alloying [pp. 2189-2194]
A.Y. Badmos and H.K.D.H. Bhadeshia

Effect of Carbon and Nitrogen on Chemical Homogeneity of Fcc Iron-Based Alloys [pp. 2195-2199]
V.G. Gavriljuk, A.L. Sozinov, A.G. Balanyuk, S.V. Grigoriev, O.A. Gubin, G.P. Kopitsa, A.I. Okorokov, and V.V. Runov

Transformations

Evolution of Recrystallization Texture from Aluminum Sheet Cold Rolled under Unlubricated Condition [pp.2217-2222]
Chang-Hee Choi and Dong Nyung Lee

Synthesis of Nanodispersed Phases during Rapid Solidification and Crystallization of Glasses in Ti₇₅Ni₂₅ Alloys [pp. 2223-2232]
R. Nagarajan, K. Aoki, and K. Chattopadhyay

Communication: Development of Reproducible and Increased Strength Properties in Thick Extrusions of Low-Alloy Al-Zn-Mg-Cu Based AA 7075 [pp. 2429-2433]
A.K. Mukhopadhyay

Communication: Discussion of "Kinetics and Phase Transformation Evaluation of Fe-Zn-Al Mechanically Alloyed Phases" [pp. 2433-2424]
Nai-Yong Tang

Authors' Reply [pp. 2434-2435]
Oswald N.C. Uwakweh and Zhentong Liu

Mechanical Behavior

Damage Effect on the Fracture Toughness of Nodular Cast Iron: Part I. Damage Characterization and Plastic Flow Stress Modeling [pp. 2245-2254]
M.J. Dong, C. Prioul, and D. François

Damage Effect on the Fracture Toughness of Nodular Cast Iron: Part II. Damage Zone Characterization Ahead of a Crack Tip [pp. 2255-2262]
M.J. Dong, C. Prioul, and D. François

Contact of Crack Surfaces during Fatigue: Part I. Formulation of the Model [pp. 2263-2275]
Ana María García, and Huseyin Sehitoglu

Contact of Crack Surfaces during Fatigue: Part II. Simulations [pp. 2277-2289]
Huseyin Sehitoglu and Ana María Garcia

Effect of Impurity Hydrogen on the Deformation and Fracture in an Al-5 Mass Pct Mg Alloy [pp. 2291-2295]
Goroh Itoh, Takeshi Jinkoji, Motohiro Kanno, and Katsumi Koyama

Effects of Test Temperature, Grain Size, and Alloy Additions on the Low-Temperature Fracture Toughness of Polycrystalline Niobium [pp. 2297-2307]
A.V. Samant and J.J. Lewandowski

Plastic-Flow and Microstructure Evolution During Hot Deformation of a Gamma Titanium Aluminide Alloy [pp. 2309-2321]
V. Seetharaman and S.L. Semiatin

Influence of Limit Stress States and Yield Criteria on the Prediction of Forming Limit Strains in Sheet Metals [pp. 2323-2333]
W.M. Sing, K.P. Rao, and K. Swaminathan

Effect of Grain Size on the Observed Pseudoelastic Behavior of a Cu-Zn-Al Shape Memory Alloy [pp. 2335-2341]
M. Somerday, R.J. Comstock, Jr., and J.A. Wert

Modeling of Rolling Texture Development in a Ferritic Chromium Steel [pp. 2343-2351]
L.S. Tóth, A. Molinari, and D. Raabe

Latent Hardening Behavior of Monocrystalline Al-Mg Solid Solution [pp. 2353-2360]
Hsin-Ming Wu, Marek A. Przystupa, and Alan J. Ardell

Environment

Welding & Joining

Solidification

Materials Processing

Retained Austenite Characteristics in Thermomechanically Processed Si-Mn Transformation-Induced Plasticity Steels [pp. 2405-2414]
A. Zarei Hanzaki, P.D. Hodgson, and S. Yue

The Influence of Austenite Grain Size and its Distribution on Chip Deformation and Tool Life during Machining of AISI 304L [pp. 2415-2422]
Laizhu Jiang, ÅKE Roos, and Ping Liu

Composite Materials